天天干夜夜撸-天天干夜夜怕-天天干夜夜骑-天天干夜夜爽-天天干夜夜爽天天操夜夜爽视频-天天干夜夜添

Welcome to the official website of Legret Metal Company
Focus on electronic welding for 20 yearsDONGGUAN LEGRET METAL.,LTD
National consultation hotline:135-2799-2739
Contact US
mobile phone: 135-2799-2739
Service hotline: 0769-38893080
Email: lzd@dglzd.com
Address: Dongguan lvzhidao Metal Co., Ltd
Contact person: Manager Zeng
Industry information

What are the characteristics of reflow welding, one of the common welding methods of electronic components?

作者:Solder manufacturer 2021-03-08 0

In the production process of electronic products, there are two common welding methods of electronic products, which are called reflow soldering and wave soldering;


The difference between the two welding methods is that the wave peak welding is mainly used to weld the plug-in circuit board, while the reflow welding is mainly used for SMT chip board welding.


Reflow welding process is to realize the soldering of mechanical and electrical connection between the welding end of surface assembly components or pins and the solder pad of printed board by remelting the paste solder which is pre distributed to the pad of printed board.


Reflow welding can control the amount of solder applied in the leading process, effectively reduce the incomplete defects of solder, such as false welding and bridge welding, so as to make the welding quality stronger, the weld joint consistency better and the reliability is very high.


During the process of electronic processing, the reflow welding does not directly dip the component into the molten solder, so the component is subject to small thermal impact (because the heating mode of reflow welding is different, in some cases, the temperature applied to the components will be higher, and the thermal stress of the corresponding components will be relatively large).


The solder for reflow welding is a commercial solder paste. It can ensure the normal composition when ordering, and it will not mix impurities in general, and it is easier to ensure the quality of welding.


If the position of solder applied on PCB is correct in the leading process and the position of the sticking component deviates from that of the component, during the reflow welding process, when all the welding ends, pins and corresponding pads of the components are wet at the same time, the effect of the surface tension of the molten solder will produce self setting effect, which can automatically correct the deviation and pull the components back to the approximate accurate position.


Local heating heat source can be used, so different welding methods can be used on the same substrate.


The process is relatively simple, and the workload of repairing electronic components is very small when the defective products appear.


主站蜘蛛池模板: 一色一情一欲一乱 | 国产日韩不卡免费精品视频 | 天天爽天天爽夜夜爽毛片 | 视频毛片 | 99热久久国产精品这里小说 | 中文字幕免费视频精品一 | 中文字幕精品久久天堂一区 | 国产三级在线免费观看 | 伊人婷婷色香五月综合缴激情 | caoporn97人人做人人爱最新 | 青青草成人影院 | 久久天天躁夜夜躁狠狠躁2019 | jizz日本zzz老师水多视频 | 国产欧美一区二区三区在线看 | 乱码中文字幕人成在线 | 久久精品国产精品亚洲综合 | 成人拍拍拍在线观看 | 国产精品亚洲片在线花蝴蝶 | 亚洲精品乱码中文字幕无线 | 久久鸭综合久久国产 | 国产日韩高清一区二区三区 | 亚洲视频日韩视频 | 特级一级毛片 | 成人黄色在线视频 | 国产精品天天干 | 91手机在线视频观看 | 亚洲 欧美 日韩在线综合福利 | 一区二区三区亚洲 | 日韩美女视频一区 | 亚洲男人天堂色 | 中文在线免费看视频 | 日本高清视频网站www | 爱爱视频在线播放 | 亚洲欧美色综合大色 | 免费番茄社区性色大片 | 亚洲欧美日韩中文综合v日本 | 欧美精品一区二区三区四区 | 天天操天天摸天天爽 | 成人中文字幕在线观看 | 共边吃奶边添下面好爽 | 乱码中文字幕人成在线 |