天天干夜夜撸-天天干夜夜怕-天天干夜夜骑-天天干夜夜爽-天天干夜夜爽天天操夜夜爽视频-天天干夜夜添

Welcome to the official website of Legret Metal Company
Focus on electronic welding for 20 yearsDONGGUAN LEGRET METAL.,LTD
National consultation hotline:135-2799-2739
Contact US
mobile phone: 135-2799-2739
Service hotline: 0769-38893080
Email: lzd@dglzd.com
Address: Dongguan lvzhidao Metal Co., Ltd
Contact person: Manager Zeng
Industry information

What should be paid attention to when using reflow solder paste? In the process of reflow soldering, what kind of change will happen?

作者:Lvzhidao solder factory 2021-03-02 0

What should be paid attention to when using reflow soldering? In the process of reflow soldering, what kind of change will happen?


1、 When the solder paste reaches the heating zone, the temperature begins to rise. The temperature rise must be slow (about 2 ℃ ~ 3 ℃ per second) to prevent boiling and splashing and to avoid the formation of small solder beads; Some components are sensitive to internal stress, which may cause fracture when the external temperature of components rises too fast( At this time, the solvent used to improve the screen printing performance and viscosity of solder paste begins to evaporate.)


2、 The flux inside the solder paste starts to be active, and the chemical cleaning action begins. The same cleaning action will take place for both water-soluble flux and free cleaning flux, but the temperature required to start the action is slightly different( At this time, the chemical cleaning action will remove the metal oxide and some contamination from the solder particles and metal to ensure that the metallurgical requirements of the "clean" solder joint surface are met


3、 When the temperature in reflow soldering furnace continues to rise, a single solder particle begins to melt, liquefy and absorb tin on the surface. In this way, all the surfaces that may be covered begin to cover and solder spots gradually form.


4、 This stage is the most important in reflow soldering. When all the individual solder particles are melted and combined with the liquid tin formed due to high temperature, the surface of solder pin begins to form under the action of surface tension. If the gap between component pin and PCB pad exceeds 0.1mm, the pin and pad may be separated under the action of surface tension, As a result, the solder joint is open.


5、 When the solder joint formed by solder paste enters the cooling zone, the solder joint begins to cool. If the cooling speed is a little faster, the strength of the solder joint will increase, but it should not be cooled too fast, otherwise it will cause the internal temperature stress of the component.




主站蜘蛛池模板: 久久91这里精品国产2020 | 国产偷国产偷亚洲高清人乐享 | 九九热久久免费视频 | 在线天堂中文在线资源网 | 久久久久久久岛国免费播放 | 久久久中文字幕日本 | 久久精品国产曰本波多野结衣 | 久久日韩精品激情 | 日本乱人伦在线观看免费 | 91久久夜色精品 | 99亚洲精品高清一二区 | 国产女精品| 波多野结衣在线一区 | 欧美一级毛片高清视频 | 91色久| 成人免费久久精品国产片久久影院 | 中文字幕在线精品视频万部 | 成人欧美深夜福利视频在线播放 | 国产高清一区二区三区免费视频 | 国产美女主播一级成人毛片 | 国产精品久久久久久久久久直 | 亚洲国产欧美在线人成北岛玲 | 欧美透逼视频 | 亚洲综合国产 | 天天摸天天做天天爽在线 | 能直接看的一级欧美毛片 | 91精品在线播放 | 91视频最新地址 | 草草在线免费视频 | 日本免费观看的视频在线 | 中文字幕在线看视频一区二区三区 | 亚州精品永久观看视频 | 久久久久久国产精品三级 | 伊人一伊人色综合网 | 中文字幕在线看视频一区二区三区 | 毛片免| 久久国产精品-久久精品 | 久久亚洲精品玖玖玖玖 | 国产成人aa在线观看视频 | 国产精品免费视频一区二区 | 日本三级中文字幕 |